А天堂中文地址在线,久久久亚洲一区二区三区,妻子的背叛完整版视频

弗爾德（上海）儀器設備有...

查看電話 在線咨詢

立即詢價

您提交后，專屬客服將第一時間為您服務

點擊提交代表您同意《用戶服務協議》《隱私政策》

Quality Control of Coal with Elemental Analyzers

閱讀：6725 發布時間：2015-05-15

Using Combustion and Thermogravimetric Analyzers from ELTRA
Coal is one of the most important fossil fuels. In 2012, the global stone coal output was about 6.6 billion
metric tons [1]. A huge amount of the worldwide traded stone coal is mined in China, USA, Russia and
India. Compared to the large amount of mined coal the required sample volume for the characterization
of coal, varying from a few mg up to 1 gram, seems unbelievably small. The characterization of coal is
important for its quality assessment and further use. Depending on the product quality, coal is suitable
for coking, steel production or electrical power generation. This article takes a look at the chemical
background of proximate and ultimate coal analysis and how these parameters are measured with
ELTRA’s combustion and thermogravimetric analyzers.
The most common types of coal (lignite, bituminous and anthracite) can be distinguished by their
different chemical and physical properties. The elements carbon (C ), hydrogen (H), nitrogen (N), sulfur
(S) and oxygen (O) are the most frequently measured elements. Additionally, the mineral content of the
ash (esp. silica, alumina, ferric oxide etc.) is determined. Coal is characterized by more or less physically
determined parameters such as moisture, volatile and ash content, and also calorific value and ash
fusion temperature.
1. Proximate coal analysis (physical testing)
Given the variety of parameters which influence the quality of coal, it seems rather ambitious to name
one parameter which best describes the coal quality. Due to the fact that coal is mostly used as fuel the
calorific value is suitable to give a first impression of the product quality.
For a first (“proximate”) analysis of coal the calorific value, the moisture, ash, and volatile content are
measured. From these data the so called fixed carbon content is calculated.
Table Nr. 1 shows the main types of coal with their calorific value and the content of volatiles.
Calorimeters for coal analysis can be divided into isoperibolic and adiabatic. In both types of calorimeter
a previously dried coal sample is introduced in a calorimetric bomb, oxygen is added and the coal is
combusted. The combustion heat is measured and gives the gross calorific value.
Very important for documentation is the “base” on which all further values are calculated. The ISO
Standard 17247:2013 defines the listed reporting basis (table 2).
AR (as received) is the most widely used basis for coal analysis. For a correct proximate analysis it is
essential to know the moisture content of the coal as this value influences all other parameters.
Moisture can be separated into surface, hydroscopic, decomposition and mineral moisture and can be
determined by the use of a furnace and an external balance or with a thermogravimetric analyzer (TGA).
The standard ASTM D7582-10 describes the proximate coal analysis by using macro thermogravimetric
analyzers. These analyzers, such as ELTRA’s TGA Thermostep, fig. 1, combine the heating and the weighing process for a convenient analysis of moisture, volatiles and ash content in one analysis cycle.
Micro thermogravimetric analyzers are not suitable for coal analysis due to the limited sample weight of
less than 10 mg. Macro TGA analyzers accept a sample weight of up to 1 gram which is weighed into
ceramic crucibles. These crucibles are placed on a carousel providing 19 positions for different samples.
The carousel is located in a heating chamber which can be purged with oxidizing atmosphere (oxygen or
air) or an inert gas (nitrogen). This chamber can be heated from room temperature to 1,000 °C and is
connected to an integrated weighing cell by a ceramic pedestal.
The moisture content of the coal is now determined by filling 1 g sample into the ceramic crucible and
heat the TGA analyzer up to 107 °C, holding the temperature until a constant mass is detected. In
contrast to the moisture content of coal, the volatile content does not consist of one species (water) but
of a mixture of aliphatic and aromatic hydrocarbons. For a correct determination of the volatiles a TGA
analyzer has to increase the temperature within 30 minutes to 950°C, holding this temperature for 7
minutes. During this heating process the crucibles are covered with lids and the heating chamber is
purged with nitrogen. For the subsequent determination of the ash content the TGA analyzer cools down
from 900 °C to 600 °C, changes to an oxygen atmosphere and heats up to 750 °C, holding this
temperature for one hour.
The whole analysis cycle is done automatically. Table (3) shows typical results of a stone coal sample
analyzed with ELTRA’s Thermostep.
The fixed carbon content is used as an estimate of the amount of coke that will be yielded from a coal
sample. It can be calculated by subtracting the measured amount of the volatile content from the sample
mass which was introduced into the ceramic crucible. The calculated fixed carbon is lower than the total
carbon content as some volatile hydrocarbons are removed during the analysis process.

2. Ultimate coal analysis (chemical analysis)
In addition to proximate coal analysis ultimate coal analysis also requires the determination of the
carbon ( C ), hydrogen (H) , nitrogen (N) , sulfur ( S), ash and oxygen (O) content by difference. According
to the ISO standard 17247 the oxygen content of a coal sample is not measured directly. This content is
calculated by adding all other values. The remaining difference to 100 % is defined to be the amount of
oxygen.
For determination of the elements C, H, N, S elemental analyzers are available. A typical elemental
analyzer combusts the coal sample and measures the combustion gas with infrared cells, a thermal
conductivity cell or a combination of both. Available analyzers differ with regards to required sample
weight, combustion temperature and measured elements.
Micro elemental analyzers offer the possibility to determine C, H, N, S in one analysis cycle, but only
accept a very small sample weight of max. 10 mg. This makes the sample preparation for these analyzers
error-prone. The requirements for the determination of the elements C, H, N are regulated in the
standard ISO 29541. Common macro elemental analyzers which fulfill these requirements use a quartz or
steel combustion tube and analyze sample weights of typically 60 - 80 mg. When using these types of
combustion tubes the applied temperature is limited to approximay 1,000 °C.
The correct determination of sulfur requires higher temperatures, because the sulfur, which is bonded as
sulfate, will not be released in the gas phase at lower temperatures. As a consequence, common sulfur
analyzers (which are described in the standard ISO 19579) use ceramic combustion tubes which can
sustain higher temperatures. Alternatively, the applied temperature can be increased by adding tin to
the coal sample. Due to the additional combustion energy of the tin, the local temperature of the sample
is higher than the temperature in the furnace. Tin is not needed when using ELTRA’s CHS 580 analyzer
(fig. 2). This analyzer also determines the carbon and hydrogen content and uses a furnace with ceramic
combustion tube which can apply temperatures up to 1500 °C.
For determination of the sulfur content approx. 150 mg of sample is weighed into a sample carrier (e. g.
a ceramic boat). The sample carrier is introduced into the hot furnace and the released combustion
gases (CO2, SO2, H2O) are measured with infrared cells.
3. Characterization of ash
The combustion residue of the coal (ash) can also be of analytical interest. Like for coal, the ash
parameters can be separated into physical or chemical properties.
For steam power generation, for example, the physical ash behaviour at different temperatures (ash
fusion test) is very important. When coal is combusted in a furnace of an electrical power plant a
powder-shaped residue or a glassy slag (clinker), which has to be removed as molten liquid, are
unwanted by-products. Not every electrical power plant is able to handle clinker-forming coal because of
the cost-intensive furnace cleaning that is required.
When using an ash fusion analyzer (such as CAF Digital from Carbolite) the ash is formed in the shape of
a cone, pyramid or a cube and is introduced into a furnace with a special window. Through this window a
camera can observe the sample’s behavior during heating. Typically, temperatures up to 1,600 °C are
applied. During the heating process parameters such as deformation, softening, hemisphere and flow
temperature are recorded. The flow temperature is crucial for deciding on the further use of the coal, for
example in steam power generation.
For chemical analysis of ash, a spectrometer can be used. The element concentration of sodium,
magnesium, aluminum etc. is important for the evaluation of the environmental impact. A nondestructive analysis method is X-ray fluorescence. Dissolution of the ash is needed when other
techniques like ICP-OES or AAS are chosen.
Conclusion
Coal and coal ash analysis requires a variety of instrumentation. Elemental and thermogravimetric
analyzers are important tools for quality control which offer fast and precise results and are easy to
operate. ELTRA offers a wide range of combustion analyzers for the determination of C, H, N, O, S in
solids as well as thermogravimetric analyzers.

提供商	弗爾德（上海）儀器設備有限公司	下載次數	346次
資料大小	393.2KB	資料類型	PDF 文件免費下載該資料
資料圖片	--	瀏覽次數	6725次

亚洲AV成人片无码网站玉蒲团,男人10处有痣是富贵痣,AV亚洲欧洲日产国码无码苍井空,日韩午夜欧美精品一二三四区

Quality Control of Coal with Elemental Analyzers

產品展示

會員登錄

收藏該商鋪

提示