亚洲AV成人片无码网站玉蒲团,男人10处有痣是富贵痣,AV亚洲欧洲日产国码无码苍井空,日韩午夜欧美精品一二三四区

蘇州東偉元電子有限公司
中級會員 | 第12年

13913158248

鼎陽
直流電源
中國臺灣儀鼎PICOTEST
德國科納沃茨特
DESCO
大立
菊水KIKUSUI
德士TEXIO電源
精久交流源
普賽斯儀表
環境試驗箱
德國EA電源
泰克Tektronix示波器
(Keithley)吉時利
同惠
盛普信號發生器
中創
大華電源
東偉元
中國臺灣固緯Gwinstek
福祿克FLUKE
青島艾諾
儀器維修

中國臺灣儀鼎 PICOTESY J2100A專業測試訊號轉換器

時間:2017/4/1閱讀:2873
分享:

中國臺灣儀鼎 PICOTESY J2100A專業測試訊號轉換器

 

J2100A Injection Transformer 1Hz~5MHz 

 
 
 
 
 
iconLow band corner frequency 達1Hz,可支援 功率因數控制器(PFC)之穩定性測試
icon5MHz帶寬足以量測大多數電源和穩壓器
icon超高頻寬,可達23 Octave
icon優異精確的低失真表現
icon5Ω終端,對待測電路的影響降至zui小
icon包括衰減功能來確保小信號的測量正確性
icon詳細規格
 
  Product Information

The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.

The usable bandwidth of an injection transformer is generally significantly greater than the 3dB frequency limits. This is because the transformer itself is outside of the measurement, leading many to incorrectly believe that the transformer is a non-critical element.

The bandwidth of the transformer is strongly related to the terminating impedance. The most network analyzers provide a 50 Ohm oscillator source impedance. Assuming this impedance the optimal termination resistor is 5 Ohms. This significantly attenuates the injection signal, which is generally beneficial, as a common error in Bode measurements is using a signal which is too large, and therefore not a small signal measurement. An added benefit of this low value is that it can generally be left in circuit at all times, simplifying the connection to the network analyzer without appreciably impacting the output voltage of the circuit being tested.

 
  Detailed Specifications:
 
Performance at -10dBm input level
CharacteristicRating
DCR 
Ratio1:1
Termination Impedance5 Ohms
Nominal 3dB Bandwidth1Hz ~ 5MHz
Isolation Voltage600V
Isolation Capacitance390pF@1KHz
DC Current10mA
Temperature Range0 ~ 50°C
Maximum Altitude6000 Ft

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

X
該信息已收藏!
標簽:
保存成功

(空格分隔,最多3個,單個標簽最多10個字符)

常用:

提示

X
您的留言已提交成功!我們將在第一時間回復您~
撥打電話
在線留言